manualshive.com logo in svg

Dell PowerConnect B-TI24x, Hardware Installation Manual

Share
Download
Dell PowerConnect B-TI24x Hardware Installation Manual Download Page 27

Dell PowerConnect B-Series TI24X Hardware Installation Guide

17

53-1002265-01

Installing the device

2

DANGER

Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. 
Particular attention should be given to supply connections other than direct connections to the 
branch circuit (e.g. use of power strips).

Follow the steps to install the rack mount brackets and mount the device in a rack.

1. Remove the rack mount kit from the shipping carton. The kit contains two mounting brackets.

2. Place the Network switch on a hard flat surface with the front panel facing you.

3. Attach a rack-mount bracket to one side of the Network switch with the supplied screws. Then 

attach the other bracket to the other side.

4. Attach retainer nuts into the non threaded holes in the four post rack. Use 10-32 screws  to 

attach brackets to the rack.

DANGER

Make sure you use the screws supplied with the mounting brackets. Using the wrong screws 
could damage the PowerConnect B-Series TI24X and would invalidate your warranty.

Figure 5

 shows how to attach the short mounting brackets.

FIGURE 5

Attaching the short mounting brackets

Mount the device in the rack as illustrated in 

Figure 6

.

Summary of Contents for PowerConnect B-TI24x



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands