manualshive.com logo in svg

Dell PowerConnect B-TI24x, Hardware Installation Manual

Share
Download
Dell PowerConnect B-TI24x Hardware Installation Manual Download Page 51

Dell PowerConnect B-Series TI24X Hardware Installation Guide

41

53-1002265-01

Replacing a power supply

5

Boot Prom MAC: 0011.1122.2233

The power supplies are numbered from left to right. These numbers assume you are facing the 
front of the device, not the rear.

If the display indicates "Installed (Failed)" for any of the slots, the power supply installed in that 
particular slot has failed.

AC power supplies

Use the following procedures for AC power supplies in PowerConnect B-Series TI24X  devices.

DANGER

Before beginning the installation, refer to the precautions in 

“Power precautions”

 on page 12.

You will need a #2 Phillips-head screwdriver to perform these procedures.

Figure 14

 shows a front view of the AC power supply.

FIGURE 14

AC power supply

Removing an AC power supply

Follow the steps to remove an AC power supply.

1. Unplug the PDU power cords (C13-C14) from the power source.

2. Disconnect the PDU power cords (C13-C14) from the power supply.

Summary of Contents for PowerConnect B-TI24x



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands