manualshive.com logo in svg

Dell PowerConnect B-TI24x, Hardware Installation Manual

Share
Download
Dell PowerConnect B-TI24x Hardware Installation Manual Download Page 28

18

Dell PowerConnect B-Series TI24X Hardware Installation Guide

53-1002265-01

Powering on the system

2

FIGURE 6

Installing the device in a rack

5. Proceed to 

“Powering on the system”

.

Powering on the system

Note the following before powering on the system:

•

The AC outlet should be installed near the equipment and should be easily accessible.

•

Get the appropriate cable for the AC outlet.

•

If your installation requires a different PDU power cords (C13-C14) than that supplied with the 
device, make sure you obtain a PDU power cords (C13-C14) displaying the mark of the safety 
agency that defines the regulations for PDU power cords(C13-C14) in your country. The mark is 
your assurance that the PDU power cords (C13-C14) can be used safely with the device.

•

Ensure that all power supplies are fully and properly inserted.

•

Remove the PDU power cords (C13-C14) from the shipping package.

•

Attach the AC PDU power cords (C13-C14) to the AC connector on the rear panel as shown in 

Figure 7

.

NOTE

Align the locating notch on the underside of the AC PDU power cords (C13-C14) before inserting. 

Summary of Contents for PowerConnect B-TI24x



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands