manualshive.com logo in svg

Dell PowerConnect B-TI24x, Hardware Installation Manual

Share
Download
Dell PowerConnect B-TI24x Hardware Installation Manual Download Page 47

Dell PowerConnect B-Series TI24X Hardware Installation Guide

37

53-1002265-01

Chapter

5

Maintaining the PowerConnect B-Series TI24X Hardware

In this chapter

•

Hardware maintenance schedule  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  37

•

Replacing a fiber optic module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  37

•

Replacing a power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  39

•

Replacing the fan tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  45

Hardware maintenance schedule

This chapter provides instructions for maintaining the PowerConnect B-Series TI24X hardware.

DANGER

The procedures in this manual are for qualified service personnel.

The PowerConnect B-Series TI24X switch hardware components require minimal maintenance. Dell 
recommends that you clean the fiber- optic connectors on fiber-optic ports and the connected fiber 
cable each time you disconnect the cable.

You can replace the following hardware components as needed:

•

Fiber optic modules (SFP+ transceivers)

•

Power supplies

•

Fan tray

Replacing a fiber optic module

You can remove an SFP or SFP+ from a port and replace it with a new one while the PowerConnect 
B-Series TI24X  is powered on and running.

This section provides information about the following tasks:

•

“Removing a fiber optic module”

•

“Installing a new fiber optic module”

•

“Cabling a fiber optic module”

Summary of Contents for PowerConnect B-TI24x



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands