manualshive.com logo in svg

Dell PowerConnect B-TI24x, Hardware Installation Manual

Share
Download
Dell PowerConnect B-TI24x Hardware Installation Manual Download Page 55

Dell PowerConnect B-Series TI24X Hardware Installation Guide

45

53-1002265-01

Replacing the fan tray

5

4. Lock the power supply in place by securing the two captive screws as shown in 

Figure 20

.

FIGURE 20

Securing the power supply in the device

5. Connect the PDU power cords (C13-C14) to the power supply.

FIGURE 21

Connecting the PDU power cords (C13-C14)

6. Power on the supply and verify that it is working properly as instructed in 

“Powering on the 

system”

 on page 18 and 

“Verifying proper operation”

 on page 19.

Replacing the fan tray

NOTE

You can replace the fan tray while the PowerConnect B-Series TI24X  device is powered on and 
running. But, you need to replace the fan tray quickly after removing it from the device, otherwise 
the device will overheat.

The fan tray is located in a slot at the rear of the PowerConnect B-Series TI24X .

This section provides information about the following topics:

Summary of Contents for PowerConnect B-TI24x



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands