manualshive.com logo in svg

Dell PowerConnect B-TI24x, Hardware Installation Manual

Share
Download
Dell PowerConnect B-TI24x Hardware Installation Manual Download Page 50

40

Dell PowerConnect B-Series TI24X Hardware Installation Guide

53-1002265-01

Replacing a power supply

5

This section provides information about the following topics:

•

Installation precautions and warnings

•

Determining which power supply failed

•

Replacing a power supply

DANGER

Power supplies are hot swappable. However, Dell recommends that you disconnect the power 
supply from AC power before installing or removing the supply. The device can be running while a 
power supply is being installed or removed, but the power supply itself should not be connected 
to a power source. Otherwise, you could be injured or the power supply or other parts of the 
device could be damaged.

Installation precautions and warnings

Follow these precautions when installing a power supply in the PowerConnect B-Series TI24X .

DANGER

Before beginning the installation, refer to the precautions in 

“Power precautions”

 on page 12.

CAUTION

Do not install the device in an environment where the operating ambient temperature might 
exceed 40°C (104°F).

CAUTION

Never leave tools inside the device.

Determining which power supply failed

The Show Chassis command displays status information for the power supplies and the fans. If you 
are not sure which Power supply has failed or you not applid AC Voltage, enter the following 
command at any CLI command prompt:

PowerConnect# show chassis

Power supply 1 (NA - NA - Regular) present, status ok

Power supply 2 not present

Fan 1 ok, speed (auto): [[1]]<->2<->3

Fan 2 ok, speed (auto): [[1]]<->2<->3

Fan 3 ok, speed (auto): [[1]]<->2<->3

Fan controlled temperature: 0.0 deg-C

Fan speed switching temperature thresholds:

         Speed 1: NM<----->30                    deg-C

         Speed 2:   25<----->40                  deg-C

         Speed 3:     35<----->90                deg-C (shutdown)

Summary of Contents for PowerConnect B-TI24x



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands