Deep Sea Electronics Plc DSE5110 Operating Manual Download Page 33

Page: 33 / 54

DSE Model 5110 Automatic Start Engine Management Instrumentation System

Part No. 057-009 5110 Operating Manual Issue 3.3 3/1/2006

11 ELECTRICAL CONNECTIONS

Connections to the Module are via plug and sockets.

11.1 CONNECTION DETAILS

The following describes the connections and recommended cable sizes to the 7 plugs and sockets on the rear

of the Module. See rear panel layout

FIG 6

11.1.1 PLUG “A” 8 WAY

PIN No

DESCRIPTION

CABLE SIZE

NOTES

DC Plant Supply Input
(Negative)

2.5mm² (13 AWG)

DC Plant Supply Input
(Positive)

2.5mm² (13 AWG)

(Recommended Maximum Fuse 21A)

Emergency Stop Input

2.5mm (13 AWG)

Plant Supply Positive. Also supplies fuel & start
outputs.
(Recommended Maximum Fuse 32A)

Fuel relay Output

2.5mm² (13 AWG)

Plant Supply Positive from pin 3. 16 Amp rated.

Start relay Output

2.5mm² (13 AWG)

Plant Supply Positive from pin 3. 16 Amp rated.

Auxiliary Output relay 1

1.0mm² (18 AWG)

Plant Supply Positive. 5 Amp rated.

Auxiliary Output relay 2

1.0mm (18 AWG)

Plant Supply Positive. 5 Amp rated.

Auxiliary Output relay 3

1.0mm (18 AWG)

Plant Supply Positive. 5 Amp rated.

11.1.2 PLUG “B” 11 WAY

PIN No

DESCRIPTION

CABLE SIZE

NOTES

Charge fail / excite

2.5mm² (13 AWG)

Do not connect to ground (battery Negative)

Auxiliary input 1

0.5mm² (20 AWG)

Switch to Negative

Auxiliary input 2

0.5mm² (20 AWG)

Switch to Negative

Auxiliary input 3

0.5mm² (20 AWG)

Switch to Negative

Auxiliary input 4

0.5mm² (20 AWG)

Switch to Negative

Auxiliary input 5

0.5mm² (20 AWG)

Switch to Negative

15 Not

connected

Functional Earth

2.5mm² (13 AWG)

Connect to a good clean earth point

17 Magnetic

pickup

Positive

0.5mm² (20 AWG)

Connect to Magnetic Pickup device

18 Magnetic

pickup

Negative

0.5mm² (20 AWG)

Connect to Magnetic Pickup device

19 Not

connected

NOTE:- Ensure magnetic pickup screen is connected to ground at one end only.

NOTE:- Terminal numbers 20-34 are not fitted to the 5110 controller

11.1.3 PLUG “F” 4 WAY

PIN No

DESCRIPTION

CABLE SIZE

NOTES

Generator L1 voltage monitoring
input

1.0mm² (18 AWG)

Connect to generator L1 output (AC)
(Recommend 2A fuse)

Generator L2 voltage monitoring
input

1.0mm² (18 AWG)

Connect to generator L2 output (AC)
(Recommend 2A fuse)

Generator L3 voltage monitoring
input

1.0mm² (18 AWG)

Connect to generator L3 output (AC)
(Recommend 2A fuse)

Generator Neutral input

1.0mm² (18 AWG)

Connect to generator Neutral terminal
(AC)

CALL US TODAY

1-888-POWER-58

REQUEST A QUOTE

[email protected]

SHOP ONLINE

www.genpowerusa.com

Summary of Contents for DSE5110























































Search results

Summary of Contents for DSE5110

Reviews:

Related manuals for DSE5110

Brands by name

Popular brands

Deep Sea Electronics Plc DSE5110, Operating Manual

Search results

Summary of Contents for DSE5110

Reviews:

Related manuals for DSE5110

Brands by name

Popular brands