manualshive.com logo in svg

Deep Sea Electronics Plc DSE5110, Operating Manual

Share
Download
Deep Sea Electronics Plc DSE5110 Operating Manual Download Page 10

          10

         Part No. 057-009              5110 Operating Manual Issue 3.3                  3/1/2006                     

 

4.2 MANUAL 

OPERATION 

To initiate a start sequence in 

MANUAL

, press the 

 

 pushbutton. When the controller is in the manual 

mode (indicated by an LED indicator beside the button), pressing the 

START

 (I) button will initiate the 

start sequence.

 

 

NOTE:- There is no Start Delay in this mode of operation. 

 

NOTE:- When in manual mode, the remote start input cannot be used to begin the start 

sequence. 

 
If the 

pre-heat

 output option is selected this timer is then initiated, and the auxiliary output selected is 

energised. 
 
After the above delay the 

Fuel Solenoid

 is energised, then the 

Starter Motor

 is engaged. 

 
The engine is cranked for a pre-set time period. If the engine fails to fire during this cranking attempt then 
the starter motor is disengaged for the pre-set rest period. Should this sequence continue beyond the set 
number of attempts (fixed at 3), the start sequence will be terminated and 

 

Fail to Start

 

 

fault will be displayed accompanied by a flashing shutdown 

 indicator. 

 
When the engine fires, the starter motor is disengaged and locked out at a pre-set frequency from the 
Alternator output. Alternatively a Magnetic Pickup mounted on the flywheel housing can be used for 
speed detection (This is selected using the front panel editor).  
After the starter motor has disengaged, the 

Safety On

 timer is activated, allowing Oil Pressure, High 

Engine Temperature, Under-speed, Charge Fail and any delayed Auxiliary fault inputs to stabilise without 
triggering the fault. 
Once the engine is running, the 

Warm Up

 timer, if selected is initiated, allowing the engine to stabilise 

before it can be loaded. 
 
The generator will run off load, unless a 

Remote Start

 signal is applied, and if 

Load Transfer

 has been 

selected as a control source, the appropriate auxiliary output selected will activate. 
 
If the 

Remote Start

 signal is removed, the generator will continue to run 

On

 load until the 

Auto 

mode is 

selected. The 

Remote Stop Delay Timer

 will time out, the load is then disconnected. The generator will 

then run 

off

 load allowing the engine a 

cooling

 down period. 

 

NOTE:- Removing the remote start input when the set is on load will not cause the generator 

to be taken off load. 

 
Selecting 

STOP (O)

 de-energises the 

FUEL SOLENOID

, bringing the generator to a stop. 

 

CALL US TODAY 

1-888-POWER-58

REQUEST A QUOTE 

[email protected]

SHOP ONLINE 

www.genpowerusa.com

Summary of Contents for DSE5110























































Reviews:

No comments

Brands by name

Popular brands

Load more brands