manualshive.com logo in svg

Deep Sea Electronics Plc DSE5110, Operating Manual

Share
Download
Deep Sea Electronics Plc DSE5110 Operating Manual Download Page 14

          14

         Part No. 057-009              5110 Operating Manual Issue 3.3                  3/1/2006                     

 

 

OIL PRESSURE SENDER OPEN CIRCUIT,

 if the module detects a loss of signal from the oil pressure 

sender (open circuit) a shutdown is initiated. The LCD will indicate:- 

 

 (Steady) (And  ‘-----‘ on the engine oil pressure instrument). Sender failure is not delayed; it is an 

immediate shutdown

. 

 

AUXILIARY INPUTS

, if an auxiliary input has been configured as a shutdown the appropriate LCD 

segment will be displayed: - 

 

!

 

 

LOSS OF SPEED SIGNAL,

 if the speed sensing signal is lost during cranking, a shutdown is initiated.  

The 

 

 icon will illuminate (Steady). As engine speed cannot be determined, the entire “fail to stop” 

timer is observed before the alarm can be reset and the engine restarted. 
  

NOTE:- This will only occur if the controller is configured for magnetic pickup and the speed 

sensing signal is lost during cranking or during the safety on timer.  If the signal is lost during 
normal operation the Generator will shutdown with an Under-speed alarm. 

 
 
 

CALL US TODAY 

1-888-POWER-58

REQUEST A QUOTE 

[email protected]

SHOP ONLINE 

www.genpowerusa.com

Summary of Contents for DSE5110























































Reviews:

No comments

Brands by name

Popular brands

Load more brands