Deep Sea Electronics Plc DSE5110 Operating Manual Download Page 18 | Manualshive

Page: 18 / 54

background image

18

Part No. 057-009 5110 Operating Manual Issue 3.3 3/1/2006

6.3 VIEWING

THE

INSTRUMENTS

It is possible to manually scroll to display the different instruments by repeatedly operating the scroll
button. Once selected the instrument will remain on the LCD display until the user selects a different
instrument or after a period of inactivity the module will revert to the initial display (Hz/RPM).

Instrument Page Order:-

•

Frequency / RPM

•

AC Voltage Line-Neutral

(<<<Not Shown on 3 phase 3 wire (Delta) version of the module)

•

AC Voltage Line-Line

•

AC Line Current

•

Oil Pressure

•

Coolant temperature

•

Engine Hours Run

•

DC Battery Voltage

Manually Selecting an Instrument

Initial display (Hz/RPM)

Hz

RPM

51.0 1530

Pressing the

DOWN

button the LCD will

then show (Generator L-N voltages)

212.3 209.1

19

6.

7

L1- N

L2- N

L

3-

N

V

Pressing the

DOWN

button the LCD will

then show (Generator L-L voltages)

417.3 409.6 39

9

.

7

L1- L2

L2- L3

L

3

-

L

1

V

Pressing the

button again will scroll through each individual instrument eventually returning to the

original instrument displayed.

NOTE:-Once selected the instrument will remain on the LCD display until the user selects a

different instrument or after a period of inactivity the module will revert to the initial display.

CALL US TODAY

1-888-POWER-58

REQUEST A QUOTE

[email protected]

SHOP ONLINE

www.genpowerusa.com

«
...
16
17
18
19
20
...
»

Summary of Contents for DSE5110























































Reviews:

No comments

Related manuals for DSE5110

Brand: Watts Pages: 2

Brand: Hanbay Pages: 18

Brand: Kasco Pages: 3

Brand: LAE electronic Pages: 7

Brand: LAE electronic Pages: 2

Brand: National Instruments Pages: 2

Brand: Paradox Pages: 2

ZITON RADIO LOOP MODULE

Brand: EMS Pages: 26

Brand: Danfoss Pages: 30

Brand: Alde Pages: 36

YQPV-HP360V/100A

Brand: PSC Solar Pages: 22

Brand: Telit Wireless Solutions Pages: 45

Brand: YOKOGAWA Pages: 33

Brand: NXP Semiconductors Pages: 39

Alicat Scientific MC

Brand: Halma Pages: 2

Brand: VAT Pages: 94

Brand: Meilhaus Electronic Pages: 19

Brand: Bardiani Valvole Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands