Deep Sea Electronics Plc DSE5110 Operating Manual Download Page 54

Page: 54 / 54

Part No. 057-009 5110 Operating Manual Issue 3.3 3/1/2006

CONFIGURABLE INPUTS

Factory default settings are in bold italicised text.

Parameter

Selection

31 – Input 1

0 - Delayed, Warning, close to activate

1 - Delayed, Warning, open to activate

2 - Immediate, Warning, close to activate

3 - Immediate, Warning, open to activate

4 - Delayed, Shutdown, close to activate

5 - Delayed, Shutdown, open to activate

6 -Immediate, Shutdown, close to activate

7 - Immediate, Shutdown, open to activate

8 - Remote Start, close to activate

9 - Remote Start, open to activate

32 – Input 2

0 - Delayed, Warning, close to activate

1 - Delayed, Warning, open to activate

2 - Immediate, Warning, close to activate

3 - Immediate, Warning, open to activate

4 - Delayed, Shutdown, close to activate

5 - Delayed, Shutdown, open to activate

6 - Immediate, Shutdown, close to activate

7 - Immediate, Shutdown, open to activate

8 - Electrical trip, close to activate

9 - Electrical trip, open to activate

33 – Input 3

0 - Warning, Delayed, close to activate

1 - Warning, Delayed, open to activate

2 - Warning, Immediate, close to activate

3 - Warning, Immediate, open to activate

4 - Shutdown, Delayed, close to activate

5 - Shutdown, Delayed, open to activate

6 - Shutdown, Immediate, close to activate

7 - Immediate, Shutdown, open to activate

8 - Lamp test, close to activate

9 - Lamp test, open to activate

34 – Input 4

0 - Delayed, Warning, close to activate

1 - Delayed, Warning, open to activate

2 - Immediate, Warning, close to activate

3 - Immediate, Warning, open to activate

4 - Delayed, Shutdown, close to activate

5 - Delayed, Shutdown, open to activate

6 - Immediate, Shutdown, close to activate

7 - Immediate, Shutdown, open to activate

35 - Input 5

0 - Delayed, Warning, close to activate

1 - Delayed, Warning, open to activate

2 - Immediate, Warning, close to activate

3 - Immediate, Warning, open to activate

4 - Delayed, Shutdown, close to activate

5 - Delayed, Shutdown, open to activate

6 - Immediate, Shutdown, close to activate

7 - Immediate, Shutdown, open to activate

8 - Oil pressure switch, Shutdown, open for low oil pressure

9 - Oil pressure switch, Shutdown, close for low oil pressure

NOTE:- This section details the configuration editor of the “new” 5110 module. To identify the “original” and

“new” controllers, See the section entitled Identification of “original” 5110 and “new” 5110 elsewhere in this manual.

NOTE:- This page contains configuration details for the “new” V3 5110 only ! For details of the “new”(V4) 5110 and

“original” 5110 see the Front Panel configuration section elsewhere in this manual

CALL US TODAY

1-888-POWER-58

REQUEST A QUOTE

[email protected]

SHOP ONLINE

www.genpowerusa.com

Summary of Contents for DSE5110























































Search results

Summary of Contents for DSE5110

Reviews:

Brands by name

Popular brands

Deep Sea Electronics Plc DSE5110, Operating Manual

Search results

Summary of Contents for DSE5110

Reviews:

Brands by name

Popular brands