DataCard SP75 Plus Manual Download Page 96

Page: 96 / 136

Page 91

OP-01613, OP-01663 L1 or L2 Supply Error

The supply material is not ready in the L1 or L2 laminator.

Possible Cause 1:

The laminator cartridge is not fully seated in the printer.

Solution 1:

Push firmly on the laminator cartridge so it is completely in the

printer. If the cartridge cannot be pushed in all the way, remove any cards or
other objects in the way.

Possible Cause 2:

You moved the laminator supply while the cartridge was

outside of the printer, such as when powering on the printer or after a
message. The supply material is not in the correct position.

Solution 2:

Click Retry to clear the card. The next card will print and be

laminated correctly.

Possible Cause 3:

The printer did not identify the material in the laminator

cartridge correctly.

Solution 3:

Install another roll of supply material in the cartridge.

Tips for Success

•

Be sure to install all supply cartridges you plan to use before powering on
the printer or clearing a message.

Summary of Contents for SP75 Plus









































































































































Search results

Summary of Contents for SP75 Plus

Reviews:

Related manuals for SP75 Plus

Brands by name

Popular brands

DataCard SP75 Plus, Manual

Search results

Summary of Contents for SP75 Plus

Reviews:

Related manuals for SP75 Plus

Brands by name

Popular brands