DataCard SP75 Plus Manual Download Page 115

Page: 115 / 136

Page 110

PR-01715 Cover Open

The cover was opened during printing.

Possible Cause:

The top cover was not closed securely or was opened

during printing.

Solution:

Push down firmly on the front edge of the top cover until it clicks

closed.

If the cover does not close...

•

Open the printer and make sure the print ribbon cartridge is installed
correctly.

•

Check for any items inside the printer, such as a cleaning roller that is
out of place. Fix any problems that you see.

•

Make sure that no cards are stuck in the printer. Remove any cards from
inside the printer.

•

Make sure the printhead cartridge is installed correctly. The top cover will
not close if the printhead cartridge is not installed correctly.

•

Make sure that nothing outside the printer prevents the cover from
closing.

Summary of Contents for SP75 Plus









































































































































Search results

Summary of Contents for SP75 Plus

Reviews:

Related manuals for SP75 Plus

Brands by name

Popular brands

DataCard SP75 Plus, Manual

Search results

Summary of Contents for SP75 Plus

Reviews:

Related manuals for SP75 Plus

Brands by name

Popular brands