DataCard SP75 Plus Manual Download Page 51

Page: 51 / 136

Page 46

•

Running a printer cleaning card using the LCD panel is an alternative to using the “Clean Printer” button in the
Printer Toolbox. See

"Cleaning the printer" on page 21

for details on printer cleaning.

With “Diagnostics” displayed on line 1, press the Up or Down Arrow key if needed
to display “Cleaning Card” on line 2.

See

"Cleaning the printer" on page 21

to prepare the printer and the cleaning card.

Press the Enter key to start cleaning. The printer picks the cleaning card from the
input hopper and runs the cleaning cycle. The menu changes to “Printer Busy” as
the card is running.

The printer ejects the cards in the output hopper when the cleaning cycle is
complete.

The menu changes to Printer Ready when the cleaning cycle is done.

Summary of Contents for SP75 Plus









































































































































Search results

Summary of Contents for SP75 Plus

Reviews:

Related manuals for SP75 Plus

Brands by name

Popular brands

DataCard SP75 Plus, Manual

Search results

Summary of Contents for SP75 Plus

Reviews:

Related manuals for SP75 Plus

Brands by name

Popular brands