DataCard SP75 Plus Manual Download Page 65

Page: 65 / 136

Page 60

SY-01305 Data Error

The setting sent to the printer does not match printer
features.

Possible Cause 1:

A setting was sent to the printer for a module that is not

installed or enabled.

Solution 1:

Check the printer to see whether options are installed. If the

option is not present in the printer, do not send data for the option.

Possible Cause 2:

The printer was moved from one PC to another PC.

Solution 2:

Open the Properties (98 or Me), Printing Preferences (2000 and

XP), or Document Default Properties (NT) dialog box and make sure that
settings match the printer that is currently connected. Click OK to make all
settings take effect.

Related Topics:

"Features and options" on page 3

Summary of Contents for SP75 Plus









































































































































Search results

Summary of Contents for SP75 Plus

Reviews:

Related manuals for SP75 Plus

Brands by name

Popular brands

DataCard SP75 Plus, Manual

Search results

Summary of Contents for SP75 Plus

Reviews:

Related manuals for SP75 Plus

Brands by name

Popular brands