DataCard SP75 Plus Manual Download Page 52

Page: 52 / 136

Page 47

Run a laminator cleaning card

Tips for Success

•

Run a laminator cleaning card only to remove particles of holographic or clear topcoat. If you do not use
topcoat material in your printer, you do not need to run a laminator cleaning card.

•

The laminator cleaning card has adhesive on both sides; it is different from the printer cleaning card. See

Cleaning the Laminator

SP Series Info Central

for more information.

With “Diagnostics” displayed on line 1, press the Up or Down Arrow key if needed
to display “Lam Clean Card” on line 2.

Remove the protective paper from both sides of the card.

Press the Enter key to start the cleaning routine. The Ready light blinks green.

Place the card in the output hopper as shown.

Summary of Contents for SP75 Plus









































































































































Search results

Summary of Contents for SP75 Plus

Reviews:

Related manuals for SP75 Plus

Brands by name

Popular brands

DataCard SP75 Plus, Manual

Search results

Summary of Contents for SP75 Plus

Reviews:

Related manuals for SP75 Plus

Brands by name

Popular brands