DataCard SP75 Plus Manual Download Page 20

Page: 20 / 136

Page 15

The LCD panel

The SP75 Card Printer includes an LCD panel. The LCD panel
has a 2-line display, four keys, and the Status light.

This section describes what you need to know when printing
cards. See

"Printer LCD settings" on page 30

for detailed

information about viewing and changing settings.

The LCD panel provides the following:

•

Current State (line 1): Shows whether the printer is ready to
print, is busy, or is paused.

— Press the Ready

key to pause or resume the printer

(undo pause).

•

Data format (line 2)

•

Printer messages: The display shows the message number
and a short description of the problem.

— Fix the problem and then press the Ready key to clear the

message. Repeat if another message is displayed.

— See

"Printer messages" on page 52

for details about

messages.

Summary of Contents for SP75 Plus









































































































































Search results

Summary of Contents for SP75 Plus

Reviews:

Related manuals for SP75 Plus

Brands by name

Popular brands

DataCard SP75 Plus, Manual

Search results

Summary of Contents for SP75 Plus

Reviews:

Related manuals for SP75 Plus

Brands by name

Popular brands