DataCard SP75 Plus Manual Download Page 6

Page: 6 / 136

Page 1

About the printer

This guide applies to the SP75 printer.

The outside of the printer

Printer Cover.

Latch: Lift the latch to open the printer cover.

Locks: Optional locks secure supplies.

Input Hopper: Open the cover to load blank cards.

LCD Panel: Shows the printer status and any
messages. Use it to change network settings.

Ready Key: Push to pause or resume the printer.

The Status Light helps you understand printer
operation. See

"Status light" on page 11

for details.

Card out slot: Cards removed from the print area
(using the manual advance knob) exit here.

Laminator Advance Knob: Moves cards in the
laminator area.

Output Hopper: Remove completed cards.

Laminators: All SP75 printers have an L1 laminator.
Some also have an L2 laminator. They apply topcoat
or patch material to cards.

Summary of Contents for SP75 Plus









































































































































Search results

Summary of Contents for SP75 Plus

Reviews:

Related manuals for SP75 Plus

Brands by name

Popular brands

DataCard SP75 Plus, Manual

Search results

Summary of Contents for SP75 Plus

Reviews:

Related manuals for SP75 Plus

Brands by name

Popular brands