manualshive.com logo in svg

DataCard SP75 Plus, Manual, Page: 24 / 136

Share
Download
DataCard SP75 Plus Manual Download Page 24

Page 19

Open the Printer Toolbox

The Printer Toolbox icon is located in the lower right corner 
of the Windows desktop. The icon shows the status of 
communication between the printer and PC. See 

SP Series 

Info Central

 for details about the icon.

By default, the Printer Toolbox dialog box is displayed. If it 
is not, do one of the following to display it:

—  Double-click the icon. 

—  Open the Properties or Printing Preferences dialog, 

and use the Printer Toolbox choices.

Use the Printer Toolbox to:

•

Run a printer or laminator cleaning card.

•

Change color settings.

•

Print a sample card or magnetic stripe test card.

•

View the status of communication between the printer 
and PC.

•

Suspend communication

 

when not printing a card.

•

Change edge to edge settings.

•

Use Advanced Setup to change printing intensity and 
laminator settings.

Summary of Contents for SP75 Plus









































































































































Reviews:

No comments