Danfoss VLT AutomationDrive FC 300 Series, Programming Manual, Page: 166 / 211

4.1.4 1-** Load/Motor
Par.
No. # Parameter description Default value 4-set-up Change
during
operation
Conver-
sion index
Type
1-0* General Settings
1-00
Configuration Mode App.Dependent All set-ups TRUE - Uint8
1-01 Motor Control Principle App.Dependent All set-ups FALSE - Uint8
1-02 Flux Motor Feedback Source [1] 24 V encoder All set-ups FALSE - Uint8
1-03 Torque Characteristics [0] Constant torque All set-ups TRUE - Uint8
1-04 Overload Mode [0] High torque All set-ups FALSE - Uint8
1-05 Local Mode Configuration [2] As mode par 1-00 All set-ups TRUE - Uint8
1-06 Clockwise Direction [0] Normal All set-ups FALSE - Uint8
1-07 Motor Angle Offset Adjust [0] Manual All set-ups FALSE - Uint8
1-1* Motor Selection
1-10
Motor Construction App.Dependent All set-ups FALSE - Uint8
1-11 Motor Model App.Dependent All set-ups FALSE - Uint8
1-14 Damping Gain 140% All set-ups TRUE 0 Int16
1-15 Low Speed Filter Time Const. App.Dependent All set-ups TRUE -2 Uint16
1-16 High Speed Filter Time Const. App.Dependent All set-ups TRUE -2 Uint16
1-17 Voltage filter time const. App.Dependent All set-ups TRUE -3 Uint16
1-2* Motor Data
1-20
Motor Power [kW] App.Dependent All set-ups FALSE 1 Uint32
1-21 Motor Power [HP] App.Dependent All set-ups FALSE -2 Uint32
1-22 Motor Voltage App.Dependent All set-ups FALSE 0 Uint16
1-23 Motor Frequency App.Dependent All set-ups FALSE 0 Uint16
1-24 Motor Current App.Dependent All set-ups FALSE -2 Uint32
1-25 Motor Nominal Speed App.Dependent All set-ups FALSE 67 Uint16
1-26 Motor Cont. Rated Torque App.Dependent All set-ups FALSE -1 Uint32
1-29 Automatic Motor Adaptation (AMA) [0] Off All set-ups FALSE - Uint8
1-3* Adv. Motor Data
1-30
Stator Resistance (Rs) App.Dependent All set-ups FALSE -4 Uint32
1-31 Rotor Resistance (Rr) App.Dependent All set-ups FALSE -4 Uint32
1-33 Stator Leakage Reactance (X1) App.Dependent All set-ups FALSE -4 Uint32
1-34 Rotor Leakage Reactance (X2) App.Dependent All set-ups FALSE -4 Uint32
1-35 Main Reactance (Xh) App.Dependent All set-ups FALSE -4 Uint32
1-36 Iron Loss Resistance (Rfe) App.Dependent All set-ups FALSE -3 Uint32
1-37 d-axis Inductance (Ld) App.Dependent All set-ups FALSE -4 Int32
1-39 Motor Poles App.Dependent All set-ups FALSE 0 Uint8
1-40 Back EMF at 1000 RPM App.Dependent All set-ups FALSE 0 Uint16
1-41 Motor Angle Offset 0 N/A All set-ups FALSE 0 Int16
1-46 Position Detection Gain 100% All set-ups TRUE 0 Uint16
1-47 Low Speed Torque Calibration App.Dependent All set-ups TRUE - Uint8
1-5* Load Indep. Setting
1-50
Motor Magnetisation at Zero Speed 100% All set-ups TRUE 0 Uint16
1-51 Min Speed Normal Magnetising [RPM] App.Dependent All set-ups TRUE 67 Uint16
1-52 Min Speed Normal Magnetising [Hz] App.Dependent All set-ups TRUE -1 Uint16
1-53 Model Shift Frequency App.Dependent All set-ups FALSE -1 Uint16
1-54 Voltage reduction in fieldweakening 0 V All set-ups FALSE 0 Uint8
1-55 U/f Characteristic - U App.Dependent All set-ups TRUE -1 Uint16
1-56 U/f Characteristic - F App.Dependent All set-ups TRUE -1 Uint16
1-58 Flystart Test Pulses Current App.Dependent All set-ups FALSE 0 Uint16
1-59 Flystart Test Pulses Frequency App.Dependent All set-ups FALSE 0 Uint16
1-6* Load Depen. Setting
Parameter Lists
VLT
®
AutomationDrive Programmming Guide
MG33ME02 - VLT
®
is a registered Danfoss trademark 165
4 4