Daedong KIOTI CS2610 Manual Download

Page: 98 / 192

CS2610

Never touch the muffler or hot

covers.until.they.are.cooled.

down.after.running.the.engine.

or.driving.the.tractor.

•

WARNING

Turn. off.all.the.electrical.de-

vices.and.remove.the.ignition.

key.before.leaving.the.tractor..
The.horn,.turn.signal.lamp.and.

hazard. lamp. can. be. operated.

without.the.key.inserted...How-

ever,.using.these.components.

without.the.engine.started.can.

discharge.the.battery.

•

ImPORTANT

STOPPING.THE.ENGINE

1. make sure to reduce the engine

rpm before stopping the engine.

2. Depress the clutch pedal and put

all shift levers in the neutral posi-

tion.

3. Run the engine at the idle speed

for approx. 2 to 3 minutes, and

then turn the key switch to the

"oFF" position to stop the engine.

T85O532A

WARmING.UP

It is recommended always to warm

up the engine before driving in or-

der to maintain the durability of the

engine and prevent malfunction of

the engine. Before warming up the

engine, make sure that each part in

the engine is properly lubricated and

each hydraulic part is in a perfect

condition in order to prevent mal-

function in the engine as well as the

hydraulic system.

M46-EU,AU-EEC인증용-05.indd 8

2017-03-10 오전 8:27:33

Summary of Contents for KIOTI CS2610

































































































































































































Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands

Daedong KIOTI CS2610, Manual

Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands