Daedong KIOTI CS2610 Manual Download

Page: 25 / 192

safetY precautions

1. disengage the pto, lower all

implements, place all control le-

vers in the neutral position, set

the parking brake, stop the engine

and remove the key.

whEN PARKINg ThE TRACTOR

T66O120a

(1) pto shaft cover (2) pto shaft cap

whEN OPERATINg ThE PTO

1. make sure the tractor is completely

stopped, gears are in neutral and

all moving components have com-

pletely stopped before connecting,

disconnecting, adjusting, cleaning

or servicing any pto driven equip-

ment.

2. keep the pto shaft cover in place

at all times. replace the pto shaft

cap when the shaft is not in use.

3. Before installing or using pto

driven equipment, read the work-

M46O103a

shop manual and review the safety

labels attached to the equipment.

before driving an implement

through the PTO, always make

sure that all bystanders are

well away from the tractor.

when using the PTO drive with

a stationary tractor, always

make sure that the gears are

in neutral and that the parking

brake is applied.

before starting up any PTO-

driven implement hitched to

the three-point linkage, lift the

implement to its full height

and check that at least 1/4 of

the total length of the tele-

scopic section of the drive

shaft is engaged.

Ensure that implements and

attachments are properly in-

stalled and that the tractor and

implement PTO RPm ratings

match.

•

wARNINg

M46-EU,AU-EEC인증용-01.indd 15

2017-03-10 오전 8:14:36

Summary of Contents for KIOTI CS2610

































































































































































































Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands

Daedong KIOTI CS2610, Manual

Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands