Daedong KIOTI CS2610 Manual Download

Page: 92 / 192

CS2610

Stop. the. tractor. on. level.

ground,. stop.the. engine,. and.

apply.the.parking.brake.before.

checking.or.repairing.it.

. Refer.to. "Daily. inspection". in.

the.section."Service".for.fuel.

replenishment.
Read. information. titled. as.

"Danger",. "Warning",. and.

"Caution". thoroughly. for. safe.

operation.

•

CAUTION

For detailed information, refer to

"maintenance interval" in chapter 7.

PRE-OPERATION

•

Walk around inspection.

•

Check the engine oil level.

•

Check the transmission oil level

•

Check the coolant level.

•

Clean the grill and radiator screen.

•

Check the air cleaner filter.

•

Check the brake pedal.

•

Check all dash gauges and indicators.

•

Check head lights, tail lights, and

all working lights.

•

Check accessible wiring harness

for any damage.

•

Check the seat belt and

ROPS

for

damage.

•

Check all danger and warning labels.

•

Check fuel level.

•

Check all danger and warning decals.

•

visually check tire inflation and

wheel bolt tightening.

It is a good practice to know the con-

dition of your tractor before you start

it. you should do a routine check be-

fore each use.

CHECk.ITEm

M46-EU,AU-EEC인증용-05.indd 2

2017-03-10 오전 8:27:29

Summary of Contents for KIOTI CS2610

































































































































































































Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands

Daedong KIOTI CS2610, Manual

Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands