Daedong KIOTI CS2610 Manual Download

Page: 183 / 192

TROUBLESHOOTING

causE

counTErMEasurEs

4. Hydraulic system is faulty

•

Oil is leaked from pipe or hose

•

The pipe clamp is loose. Re-tighten it.

•

The pipe is cracked. Have it repaired in a workshop.

•

3-point hitch cannot be lowered

•

3-point hitch safety lock function activated, one touch button

pressed

•

The valve and cylinder are damaged.

Contact

KioTi

dealer.

•

3-point hitch cannot be lifted

•

The transmission fluid is insufficient.

Add it to the specified level.

•

There is air in the intake pipe. Bleed the pipe.

•

The oil filter is clogged. Replace it.

•

The hydraulic filter, valve and cylinder are malfunctioning.

Contact

KioTi

dealer.

•

3-point hitch vibrates by itself

•

Each sensor malfunctioning, Contact

KioTi

dealer.

•

Select the highest top link hole.

5. Electric system is faulty

•

Headlamps cannot be turned on

or are dim.

•

The fuse is blown. Check the wiring and replace the fuse.

•

The bulb is blown. Replace it

•

The ground and terminal wirings are poorly contacted.

Check and clean them.

•

The battery electrolyte level is low. Charge the battery.

M46-EU,AU-EEC인증용-09.indd 5

2017-03-10 오전 8:51:15

Summary of Contents for KIOTI CS2610

































































































































































































Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands

Daedong KIOTI CS2610, Manual

Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands