Daedong KIOTI CS2610 Manual Download

Page: 19 / 192

safetY precautions

Tg2O109a

• avoid crossing steep slopes if pos-

sible. if you must do so, avoid any

holes or depressions on the down-

hill side. avoid any stumps, rocks,

bumps or raised areas on the uphill

side.

PRECAUTIONS dURINg OPERATION

whEN STARTINg ThE ENgINE

T66O108a

2. avoid accidental contact with gear

shift levers while the engine is run-

ning. unexpected tractor move-

ments can result in bodily injury or

death.

1. enter or leave the tractor leftward

griping hand rail on a fender.

M46O108a

do not jump on or off the

tractor. It may cause injuries.

Always face the tractor, use

the hand rails and steps, and

get on or off slowly. maintain a

minimum three point contact

to avoid falling. (both hands

on rails and one foot on the

step, or one hand on the hand

rail and both feet on the steps)

•

wARNINg

M46-EU,AU-EEC인증용-01.indd 9

2017-03-10 오전 8:14:34

Summary of Contents for KIOTI CS2610

































































































































































































Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands

Daedong KIOTI CS2610, Manual

Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands