Daedong KIOTI CS2610 Manual Download

Page: 94 / 192

CS2610

make.sure.that.the.brake.pedals.

are.fully.depressed.before.pull-

ing.the.parking.brake.lever.up.

•

ImPORTANT

4. press the pTo lever to the "Disen-

gage" position.

1. make sure there is no hazardous

obstacle around the tractor.

2. make sure the parking brake is set
(1) Depress the parking brake ped-

al and pull the lever up. (Check

that the parking brake lamp on

the gauge board illuminates)

(2) To release the parking brake

press the brake pedals again.

(1) pTo Clutch lever

(2) Range Gear Shift lever (Hi-N-lo)

(3) Forward / Reverse Driving pedal

(1) parking Brake lever (2) Brake pedal

(A) Depressing

(B) pressing up

M46O446A

M46O447A

M46-EU,AU-EEC인증용-05.indd 4

2017-03-10 오전 8:27:30

Summary of Contents for KIOTI CS2610

































































































































































































Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands

Daedong KIOTI CS2610, Manual

Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands