Daedong KIOTI CS2610 Manual Download

Page: 97 / 192

opERATIoN

If.driving.the.tractor.for.an.ex-

tended.period.of.time.with.the.

charge.warning.lamp."ON",.

the.battery.can.be.discharged.

and. the. tractor’s. electrical.

system.can.be.damaged.

•

WARNING

The.engine.can.be.severely.

damaged.if.it.is.run.with.the.oil.

pressure.warning.lamp."ON".

•

WARNING

M46O502A

(1) Instrument panel

(2) Engine oil pressure Warning lamp

(3) Charge Warning lamp

1. If the oil pressure warning lamp (2)

does not go "oFF" in 4 to 5 sec-

onds after the engine is properly

started, stop the engine immedi-

ately and check the engine oil lev-

el. If the engine oil level is proper,

contact your local

kIOTI

Dealer.

2. If the charge warning lamp (3)

does not go "oFF" in 4 to 5 sec-

onds after the engine is properly

started, it means that the battery

is not being charged. Have the

charging system, such as the bat-

tery and alternator, serviced.

3. Refer to "Instrument panel" in

chapter 4 for detailed information

about other indicators and lamps.

ENGINE.CHECk.lAmPS

12. Ensure that all the warning lamps

on the instrument cluster are

"oFF".

If any lamp remains on, immediately

stop the engine and determine the

cause.

M46-EU,AU-EEC인증용-05.indd 7

2017-03-10 오전 8:27:33

Summary of Contents for KIOTI CS2610

































































































































































































Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands

Daedong KIOTI CS2610, Manual

Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands