Daedong KIOTI CS2610 Manual Download

Page: 80 / 192

Cs2610

(1) pTO Clutch Lever

(A) engage

(b) disengage

PTO CluTCH lEvER

To connect the selected pTO, move

the pTO clutch lever to the left, front

and then to the right.
To disengage the pTO clutch, move

the lever to the left and then rear.
To engage the pTO, move the pTO

shift lever to the desired position and

pTO clutch lever to the engagement

position.

M46O435A

Gauge wheels must be adjusted ac-

cording to the cutting height setting.

Use the following chart for gauge

wheel position.

CuTTING HEIGHT

POSITION

(On control lever)

FRONT and REAR

GAuGE wHEEl

HEIGHT

(Ground to center

of wheel)

1.0"

66 mm (2.60 in.)

1.5"

78 mm (3.07 in.)

2.0"

91 mm (3.58 in.)

2.5"

104 mm (4.09 in.)

3.0"

97 mm (3.82 in.)

3.5"

109 mm (4.29 in.)

4.0"

102 mm (4.02 in.)

Most PTO devices gives the

most effective results when in

540 ± 10 rpm. The tachometer

has a mark that indicates 540

rpm for effective PTO opera-

tion. Operating any PTO de-

vice in faster RPM can result

in poor efficiency and danger.

•

IMPORTANT

To change pTO selection, the

pTO clutch should be disen-

gaged. Also, it should be disen-

gaged when trying to start the

engine.

•

NOTE

M46-EU,AU-EEC인증용-04.indd 22

2017-06-16 오후 1:07:04

Summary of Contents for KIOTI CS2610

































































































































































































Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands

Daedong KIOTI CS2610, Manual

Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands