Daedong KIOTI CS2610 Manual Download

Page: 126 / 192

cs2610

T66O122A

C56O140A

(1) Lock Pin

Make sure that the PTO safety

cover is in its position before

driving the PTO shaft.

Never go close to the rotating

PTO or tractor PTO shaft. A

severe accident can happen.

Before driving an implement

with the PTO, always make

sure that all bystanders are

well away from the tractor.

When using the PTO drive with

a stationary tractor, always

make sure that the gears are

in neutral and that the parking

brake is applied.

surrounding parts should not

interfere with the tractor PTO

and PTO shaft.

Before starting up any PTO-

driven implement hitched to

the three-point linkage, lift the

implement to its full height and

check that at least 1/4 of the total

length of the telescopic section

of the drive shaft is engaged.

•

WARNINg

M55O626A

Refer to the chart below when install-

ing of an universal joint.

(1) PTO cover

(A) Allowable angle of universal joint: 50˚

Allowable angle of universal joint

50 degree

The type of PTO shaft

sAE 1-3 / 8" 6 splines

M46-EU,AU-EEC인증용-06.indd 10

2017-04-26 오전 11:41:55

Summary of Contents for KIOTI CS2610

































































































































































































Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands

Daedong KIOTI CS2610, Manual

Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands