Daedong KIOTI CS2610 Manual Download

Page: 104 / 192

CS2610

To.avoid.accidents:

make.sure. the. pins. are.prop-

erly.installed.and.secured.

•

CAUTION

To.avoid.accidents:

make.sure.to.set.the.ROPS.up-

right.and. fasten. the. seat. belt.

during.work.

. If.it.is.necessary.to.work.with.

it. folded,. do. not. fasten. the.

seat.belt.

. It.can.be.dangerous.in.case.of.

tractor.rollover.

•

CAUTION

RAISING.THE.ROPS.TO.UPRIGHT.POSITION

1. pull the set pin forward.
2. Raise

ROPS

to the upright position.

3. Align it to the groove and pull the

set pin to release it.

(1) Grip Bolt

(2) Set pin

3. Align it to the groove and pull the

set pin to release it.

4. Fix the

ROPS

with the grip bolt.

M46O509A

M46O510A

(1) Grip Bolt

(2) Set pin

M46O507A

M46-EU,AU-EEC인증용-05.indd 14

2017-03-10 오전 8:27:37

Summary of Contents for KIOTI CS2610

































































































































































































Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands

Daedong KIOTI CS2610, Manual

Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands