Daedong KIOTI CS2610 Manual Download

Page: 142 / 192

cs2610

MAINTENANCE CODE

hOW TO DIsCONNECT ThE hOOD (A)

(1) hood

(2) handle

(a) pull

M46O701A

OPENINg SIdE COvER (B)

(1) hood

(1) side cover

(2) Bolt

1. the hood can be opened by pull-

ing down or the handle loosen or

the lower right hand side of tractor.

push down ward or bonnet to re-

lease latch.

2. to close the hood, press its front

down until it is locked in its posi-

tion.

3. Do not apply excessive force to

the handle to fix it. The hood can

be damaged.

1. the side covers (lh/rh) should

be removed in order to access the

engine components.

2. unscrew 2 mounting bolts and re-

move the side cover.

M46O702A

M46O703A

Be careful not to trap your

fingers when closing the side

cover.

Never open the side covers

while the engine is running.

•

CAUTION

if noise is heard from the hood

during driving, check the rubber

molding and replace it if dam-

aged.

•

NOTE

Never open the hood while the

engine is running.

•

CAUTION

M46-EU,AU-EEC인증용-07.indd 8

2017-04-25 오후 4:59:56

Summary of Contents for KIOTI CS2610

































































































































































































Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands

Daedong KIOTI CS2610, Manual

Search results

Summary of Contents for KIOTI CS2610

Reviews:

Related manuals for KIOTI CS2610

Brands by name

Popular brands