CTS iCPE User Manual Download Page 80

Page: 80 / 145

Click

Edit

to view and edit current IEEE 802.1Q Tag VLAN setting and then the following screen

page appears.

Click

to make the current VLAN settings effective.

Current/Total/Max VLANs:

View-only field.

Current:

This shows the number of currently registered VLAN.

Total:

This shows the number of total registered VLANs.

Max:

This shows the maximum number of available concurrent VLANs to be registered.

VLAN ID:

the ID for the currently registered VLAN.

VLAN Name:

Specify the name for the currently registered VLAN.

VLAN Member:

Shows the ports to be the members of the currently registered VLAN.

3.4.6.2.2 VLAN Interface

Click the option

VLAN Interface

from the

IEEE 802.1q Tag VLAN

menu and then the following

screen page appears.

Summary of Contents for iCPE


















































































































































Search results

Summary of Contents for iCPE

Reviews:

Related manuals for iCPE

Brands by name

Popular brands

CTS iCPE, User Manual

Search results

Summary of Contents for iCPE

Reviews:

Related manuals for iCPE

Brands by name

Popular brands