CTS iCPE User Manual Download Page 63

Page: 63 / 145

Telnet Port:

Specify the desired TCP port number for the Telnet console. The default TCP port

number of the Telnet is 23.

System Time Out:

Specify the desired time that the Managed Switch will wait before disconnecting

an inactive console/telnet. Specifying “0” means an inactive connection will never be disconnected.

Click the

“OK”

button to apply the settings.

3.3.4 Time Server Configuration

Click the option

Time Server Configuration

from the

Network Management

menu and then the

following screen page appears.

Time Synchronization:

Enable or disable time synchronization.

Time Server Address:

Specify the primary

NTP time server address.

Time Server Address:

When the default time server is down, the Gateway Controller will

automatically connect to the 2

time server.

Synchronization Interval:

The time interval to synchronize from NTP time server. The allowable

Summary of Contents for iCPE


















































































































































Search results

Summary of Contents for iCPE

Reviews:

Related manuals for iCPE

Brands by name

Popular brands

CTS iCPE, User Manual

Search results

Summary of Contents for iCPE

Reviews:

Related manuals for iCPE

Brands by name

Popular brands