CTS iCPE User Manual Download Page 4

Page: 4 / 145

Table of Content

....................................................................................................................... 8

1.1 Management Preparations ............................................................................................................ 8

1.1.1 Connecting the gateway controller

.............................................................................. 8

1.1.2 Assigning IP Addresses

............................................................................................. 8

2. Command Line Interface (CLI)

......................................................................................... 10

2.1 Remote Console Management-Telnet ........................................................................................ 10

2.2 Navigating CLI ............................................................................................................................11

2.2.1 General Commands

................................................................................................. 11

2.2.2 Quick Keys

............................................................................................................. 12

2.2.3 Command Format

................................................................................................... 12

2.2.4 Login Username & Password

................................................................................... 14

2.3 User Mode .................................................................................................................................. 14

2.4 Privileged Mode ......................................................................................................................... 15

2.4.1 Copy-cfg Command

................................................................................................ 15

2.4.2 Firmware Command

................................................................................................ 16

2.4.3 Reload Command

.................................................................................................... 16

2.4.4 Write Command

...................................................................................................... 17

2.4.5 Configure Command

............................................................................................... 17

2.5 Configuration Mode ................................................................................................................... 17

2.5.1 Entering Interface Numbers

...................................................................................... 18

2.5.2 No Command

......................................................................................................... 18

2.5.3 Show Command

...................................................................................................... 18

2.5.4 IP Command

........................................................................................................... 21

2.5.5 MAC Command

...................................................................................................... 23

2.5.6 Management Command

........................................................................................... 23

2.5.7 Mirror Command

.................................................................................................... 24

2.5.8 MQTT Command

.................................................................................................... 24

2.5.9 NTP Command

....................................................................................................... 26

2.5.10 QoS Command

...................................................................................................... 27

2.5.11 Security Command

................................................................................................ 33

2.5.12 SNMP-Server Command

........................................................................................ 33

2.5.13 Switch Command

.................................................................................................. 36

Summary of Contents for iCPE


















































































































































Search results

Summary of Contents for iCPE

Reviews:

Related manuals for iCPE

Brands by name

Popular brands

CTS iCPE, User Manual

Search results

Summary of Contents for iCPE

Reviews:

Related manuals for iCPE

Brands by name

Popular brands