CTS iCPE User Manual Download Page 127

Page: 127 / 145

127

Ping:

Ping can help you test the network connectivity between the Gateway Controller and the host.

You can also specify count s, timeout and size of the Ping packets.

Event Log:

Event log can keep a record of

system’s log events such as system warm start, cold

start, link up/down, user login/logout, etc.

HTTP Upgrade:

This

allows users to update the latest firmware, save current configuration or

restore previous configuration to the Gateway Controller.

FTP/TFTP Upgrade:

This

allows users to update the latest firmware, save current configuration

or restore previous configuration to the Managed Switch.

Load Factory Setting:

Load Factory Setting will set the configuration of the Managed Switch

back to the factory default settings. The IP and Gateway addresses will be set to the factory default
as well.

Load Factory Setting Except Network Configuration:

Selecting this function will also restore

the configuration of the Managed Switch to its original factory default settings. However, this will
not reset the IP and Gateway addresses to the factory default.

3.10.1 Ping

Ping

can help you test the network connectivity between the Managed Switch and the host. Select

Ping

from the

System Utility

menu and then the following screen page appears.

Summary of Contents for iCPE


















































































































































Search results

Summary of Contents for iCPE

Reviews:

Related manuals for iCPE

Brands by name

Popular brands

CTS iCPE, User Manual

Search results

Summary of Contents for iCPE

Reviews:

Related manuals for iCPE

Brands by name

Popular brands