manualshive.com logo in svg

Copystar CS 181, Service Manual

Share
Download
Copystar CS 181 Service Manual Download Page 11

2KJ/2KH

CONTENTS

1-1 Specifications

1-1-1 Specifications..........................................................................................................................................1-1-1
1-1-2 Parts names............................................................................................................................................1-1-4

(1) Body ..................................................................................................................................................1-1-4
(2) Operation panel.................................................................................................................................1-1-5

1-1-3 Machine cross section ............................................................................................................................1-1-6

1-2 Installation

1-2-1  Installation environment .........................................................................................................................1-2-1
1-2-2 Unpacking and installation ......................................................................................................................1-2-2

(1) Installation procedure ........................................................................................................................1-2-2
(2) Setting initial copy modes................................................................................................................1-2-11

1-2-3 Installing the key counter (option) .........................................................................................................1-2-12
1-2-4 Installing the cassette heater (option) ...................................................................................................1-2-17
1-2-5 Installing the cassette heater for paper feeder (option) (22 ppm model only).......................................1-2-19

1-3 Maintenance Mode

1-3-1 Maintenance mode .................................................................................................................................1-3-1

(1) Executing a maintenance item ..........................................................................................................1-3-1
(2) Maintenance modes item list.............................................................................................................1-3-2
(3) Contents of the maintenance mode items.........................................................................................1-3-5

1-3-2 Management mode ...............................................................................................................................1-3-68

(1) Using the management mode .........................................................................................................1-3-68
(2) Setting the job accounting ...............................................................................................................1-3-69
(3) Copy default ....................................................................................................................................1-3-70
(4) Machine default ...............................................................................................................................1-3-71
(5) MP Tray setting ...............................................................................................................................1-3-73
(6) Checking the total counter and printing out the counter report .......................................................1-3-73
(7) Report output...................................................................................................................................1-3-73
(8) Language setting.............................................................................................................................1-3-73

1-4 Troubleshooting

1-4-1 Paper misfeed detection .........................................................................................................................1-4-1

(1) Paper misfeed indication ...................................................................................................................1-4-1
(2) Paper misfeed detection conditions ..................................................................................................1-4-2
(3) Paper misfeeds .................................................................................................................................1-4-8

1-4-2 Self-diagnosis .......................................................................................................................................1-4-16

(1) Self-diagnostic function ...................................................................................................................1-4-16
(2) Self diagnostic codes ......................................................................................................................1-4-17

1-4-3 Image formation problems ....................................................................................................................1-4-25

(1) No image appears (entirely white)...................................................................................................1-4-26
(2) No image appears (entirely black)...................................................................................................1-4-26
(3) Image is too light. ............................................................................................................................1-4-27
(4) Background is visible.......................................................................................................................1-4-27
(5) A white line appears longitudinally. .................................................................................................1-4-27
(6) A black line appears longitudinally. .................................................................................................1-4-28
(7) A black line appears laterally...........................................................................................................1-4-28
(8) One side of the copy image is darker than the other.......................................................................1-4-28
(9) Black dots appear on the image......................................................................................................1-4-28

(10) Image is blurred...............................................................................................................................1-4-29
(11) The leading edge of the image is consistently misaligned with the original. ...................................1-4-29
(12) The leading edge of the image is sporadically misaligned with the original. ...................................1-4-29
(13) Paper creases. ................................................................................................................................1-4-29
(14) Offset occurs. ..................................................................................................................................1-4-30
(15) Image is partly missing....................................................................................................................1-4-30
(16) Fusing is poor..................................................................................................................................1-4-30
(17) Image is out of focus. ......................................................................................................................1-4-30
(18) Image center does not align with the original center. ......................................................................1-4-31

1-4-4 Electric problems ..................................................................................................................................1-4-32
1-4-5 Mechanical problems ............................................................................................................................1-4-36

Summary of Contents for CS 181




































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands