manualshive.com logo in svg

Copystar CS 181, Service Manual

Share
Download
Copystar CS 181 Service Manual Download Page 67

2KJ/2KH

1-3-27

U076

Executing DP automatic adjustment
Description

Uses a specified original and automatically adjusts the following items in the DP scanning section.
Adjusting the DP magnification (U070)
Adjusting the DP scanning timing (U071)
Adjusting the DP center line (U072)
When you run this maintenance mode, the preset values of U070, U071 and U072 will also be updated.

Purpose

To perform automatic adjustment of various items in the DP scanning section.

Method

1. Set a specified original (P/N: 302AC68243) in the DP.

Cut the trailing edge of the original.

Figure 1-3-14

2. Press the start key.
3. Press the start key. Auto adjustment starts.

When adjustment is complete, each adjusted value is displayed.

If a problem occurs during auto adjustment, DATA: XX (XX is replaced by an error code) is displayed 
and operation stops. Should this happen, determine the details of the problem and either repeat the pro-
cedure from the beginning, or adjust the remaining items manually by running the corresponding main-
tenance items.

Completion

Press the stop/clear key after auto adjustment is complete. The screen for selecting a maintenance item is
displayed.
If the stop/clear key is pressed during auto adjustment, adjustment stops and no settings are changed.

Maintenance

item No.

Description

F

R

5 mm

149 ± 1 mm

74 ± 1 mm

Display

Description

CONVEY SPEED

DP magnification in the auxiliary scanning direction

LEAD EDGE ADJ

DP leading edge registration

DP CENTER

DP original center line

Summary of Contents for CS 181




































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands