manualshive.com logo in svg

Copystar CS 181, Service Manual

Share
Download
Copystar CS 181 Service Manual Download Page 91

2KJ/2KH

1-3-51

U342

Setting the ejection restriction
Description

Sets or cancels the restriction on the number of sheets to be ejected continuously when the internal eject tray 
is selected as the eject location.

Purpose

According to user request, sets or cancels restriction on the number of sheets.

Setting

1. Press the start key.
2. Select ON or OFF using the cursor up/down keys.

Initial setting: ON
Details of restriction (number of sheets to be ejected continuously after the start key is pressed)

3. Press the start key. The setting is set.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

U343

Switching between duplex/simplex copy mode
Description

Switches the initial setting between duplex and simplex copy.

Purpose

To be set according to frequency of use: set to the more frequently used mode.

Setting

1. Press the start key.
2. Select ON or OFF using the cursor up/down keys.

Initial setting: OFF 

3. Press the start key. The setting is set.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Description

ON

Sets restriction on the number of sheets

OFF

Cancels restriction on the number of sheets

Condition

Number of sheets

When no optional ejection device is installed 

250

When the job separator is installed

150

When the built-in finisher is installed

100

Display

Description

ON

Duplex copy

OFF

Simplex copy

Summary of Contents for CS 181




































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands