manualshive.com logo in svg

Copystar CS 181, Service Manual

Share
Download
Copystar CS 181 Service Manual Download Page 149

2KJ/2KH

1-4-35

(16)
The message 
requesting cover to 
be closed is dis-
played when the front 
cover or left cover is 
closed.

1. Poor contact in the con-

nector terminals of front 
cover safety switch or left 
cover safety switch.

Reinsert the connector. Also check for continuity within the con-
nector cable. If none, remedy or replace the cable.

2. Defective front cover 

safety switch or left cover 
safety switch.

Check for continuity across each switch. If there is no continuity 
when the switch is on, replace it.

(17)
Others.

1. Wiring is broken, shorted 

or makes poor contact.

Check for continuity. If none, repair.

Problem

Causes

Check procedures/corrective measures

Summary of Contents for CS 181




































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands