manualshive.com logo in svg

Copystar CS 181, Service Manual

Share
Download
Copystar CS 181 Service Manual Download Page 204

2KJ/2KH

1-5-52

6. Release hooks at the front side of the right 

fuser unit and pull out the fuser heater.

Caution

Do not touch the glass section of the fuser 
heater.

Figure 1-5-86

7. Replace the fuser heater.
8. Straighten the fuser heater wire in the rear 

side of the new fuser heater, and insert it 
from the front side of the right fuser unit.

9. Fit both the protrusions in the front and rear 

sides of the fuser heater into the notch posi-
tions of the right fuser unit.
Insert the wire between the hooks in the 
front side of the right fuser unit until it clicks 
to secure it.

Figure 1-5-87

Fuser heater

Hook

Right fuser unit

Hook

Protrusion

Rear side

Protrusion

Hook

Front side

Summary of Contents for CS 181




































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands