Copystar CS 181 Service Manual Download Page 173

Page: 173 / 355

2KJ/2KH

1-5-21

(8) Detaching and refitting the left registration roller

Follow the procedure below to replace the left registration roller.

Procedure

1. Remove the paper conveying unit (see page

1-5-16).

2. Release the stoppers at the front and rear

side, and then remove the left registration
roller from the paper conveying unit.

Figure 1-5-33

3. Remove two stoppers, gear and two

bushes.

4. Replace the left registration roller and refit

all the removed parts.

Figure 1-5-34

Left registration roller unit

Paper conveying unit

Stopper

Left registration roller

Stopper

Bush

Gear

Summary of Contents for CS 181




































































































































































































































































































































































Search results

Summary of Contents for CS 181

Reviews:

Brands by name

Popular brands

Copystar CS 181, Service Manual

Search results

Summary of Contents for CS 181

Reviews:

Brands by name

Popular brands