CDD-562L/564 Demodulator with IP Module
Revision 2
Appendix D
MN/CDD564L.IOM
D–14
Parameter
Type
Command
(Instruction
Code and
Qualifier)
Arguments for
Command or
Response to
Query
Description of Arguments
Response to
Command
Query
(Instruction
Code and
Qualifier)
Response to Query
SNMP Trap
Destination IP
Address
STA= 15
bytes,
Numerical
Command or Query.
Sets the IP address of the SNMP Trap destination IP Address where traps will be sent, in
the format xxx.xxx.xxx.xxx where:
xxx.xxx.xxx.xxx is the IP addresss
Example: <1/STA=010.006.030.001
Note: If not configured it returns >0001/STA=0.0.0.0
STA =
STA!
STA?
STA=xxx.xxx.xxx.xxx (see
Description of Arguments)
SNMP Trap
Destination IP
Address-2
STB= 15
bytes,
Numerical
Command or Query.
Sets the IP address of the SNMP Trap destination IP Address where traps will be sent, in
the format xxx.xxx.xxx.xxx where:
xxx.xxx.xxx.xxx is the IP addresss
Example: <1/STA=010.006.030.001
Note: If not configured it returns >0001/STB=0.0.0.0
STB =
STB!
STB?
STB = xx.xxx.xxx.xxx (see
Description of Arguments)
SNMP Trap Version STV=
1 byte, value of
0 or 1
Command or Query.
Specifies the version of SNMP traps that should be sent, where:
1 = Snmpv1
2 = Snmpv2
STV =
STV!
STV?
STV = x
(see Description of Arguments)
SNMP
Write Community
SWC= 255
bytes,
characters, no
spaces
Command or Query.
Assigns SNMP write community string.
Example: <1/SWC=public
Note: Empty string is not allowed
SWC =
SWC!
SWC?
SWC =x
(see Description of Arguments)
System Working
Mode
SWM=
1 byte, value of
0 through 1
Command or Query.
Sets the system working mode, where:
1 = Router - Small Network
2 = Router - Large Network
3 = Router - Point to Point
4 = Router - Vipersat
5 = EasyConnect.
Note: Router-Vipersat mode needs the Vipersat option to be available on the modem.
Changing the address/working mode may reboot the modem.
SWM=
SWM!
SWM?
SWM =x
(see Description of Arguments)
Transmit DES
enable/disable
TDE=
1 byte, value of
0, 1, 2 or 3
Command or Query.
Enables or disables the Transmit 3xDES feature, where:
0 = Disabled
1 = Enabled (EasyConnect Only mode)
2 = PerRoute (read-only when FAST feature is purchased in router mode)
3 = Unavailable (read-only when FAST feature not purchased)
Note: Acts as command only in EasyConnect mode; on router mode, it is read-only.
Restriction: Cannot enable if the 3xDES FAST feature has not been purchased.
TDE =
TDE!
TDE?
TDE =x
(see Description of Arguments)
Summary of Contents for Vipersat CDD-562L
