Home
/
Cisco
/
Small Business SPA525G2
/
Administration Manual

Cisco Small Business SPA525G2, Administration Manual, Page: 162 / 371

Share

Page: 162 / 371

Cisco Small Business SPA525G2 Administration Manual Download Page 162

Configuring Security, Quality, and Network Features

Configuring VLAN Settings

Cisco Small Business SPA300 Series, SPA500 Series, and WIP310 IP Phone Administration Guide

162

5

LLDP-MED Extended Power-Via-MDI TLV

In the TLV for the outgoing LLDPDU, the binary value for Power Type is set to “0 1”
to indicate the power type for phone is PD Device. The Power source for the
phone is set “PSE and local” with binary value “1 1”. The Power Priority is set to
binary “0 0 0 0” to indicate unknown priority while the Power Value is set to
maximum power value based on phone type:

For the incoming LLDPDU, the TLV is ignored and not validated. Only one TLV is
allowed in the outgoing and incoming LLDPDUs. The phone will send out the TLV
for wired network only.

The LLDP-MED standard was originally drafted in the context of Ethernet.
Discussion is ongoing for LLDP-MED for Wireless Networks. Refer to ANSI-TIA
1057, Annex C, C.3 Applicable TLV for VoWLAN, table 24. It is recommended that
the TLV is not applicable in the context of the wireless network. This TLV is
targeted for use in the context of PoE and Ethernet. The TLV, if added, will not
provide any value for network management or power policy adjustment at the
switch.

LLDP-MED Inventory Management TLV

This TLV is optional for Device Class III. For the outgoing LLDPDU, we support only
Firmware Revision TLV. The value for the firmware revision is the firmware version.
For the incoming LLDPDU, the TLVs are all ignored and not validated. Only one
Firmware Revision TLV is allowed for the outgoing and incoming LLDPDUs.

Final Network Policy Resolution and QoS For the Phone

The following sections describe network policy and QoS for the IP phones.

Special VLANs

VLAN=0, VLAN=1 and VLAN=4095 are treated the same way as an untagged
VLAN. As the VLAN is untagged, CoS is not applicable.

Phone Type

Power Value

Cisco SPA525G or Cisco SPA525G2

125

Cisco SPA500 Series

120

Cisco SPA300 Series

100

«
...
160
161
162
163
164
...
»

Summary of Contents for Small Business SPA525G2




















































































































































































































































































































































































Reviews:

No comments