Cisco Linksys PAP2 Administration Manual Download Page 30

Page: 30 / 280

Getting Started

Using the Web Administration User Interface

Cisco SPA and Wireless IP Phone Administration Guide

Using the Web Administration Tabs

The following graphics show all Admin Login

advanced

tabs that appear on your

web UI pages. When viewing in User Login or basic view, fewer tabs are visible.

Each tab contains different parameters. Some tasks require you to set parameters
in different tabs.

For field reference about each parameter available on the web UI, see

Appendix B, “SPA and Wireless IP Phone Field Reference.”

Roadmap to Web UI Features

The following tables provide a roadmap to features available on the web UI.

To perform these tasks...

On the web UI, click the ...

View phone, extension, and line/call information
such, including:

•

DHCP, current IP address, DNS addresses

•

Software and hardware versions

•

Broadcast, RTP, and SIP information

•

Registration state

•

Packets sent, received, lost, and other
information

Info tab

See

“Viewing Phone

Information” section on
page 31

Configure system-level parameters, including
network and debug parameters. To:

•

Enable the web UI and web administrator
access

•

Set the Internet connection type to DHCP

•

Configure the syslog and debug servers

•

Enable VLAN and CDP

System tab

See

Chapter 6, “Configuring

Security, Quality, and Network
Features.”

Summary of Contents for Linksys PAP2

























































































































































































































































































Search results

Summary of Contents for Linksys PAP2

Reviews:

Related manuals for Linksys PAP2

Brands by name

Popular brands

Cisco Linksys PAP2, Administration Manual

Search results

Summary of Contents for Linksys PAP2

Reviews:

Related manuals for Linksys PAP2

Brands by name

Popular brands