manualshive.com logo in svg

Cisco Linksys PAP2, Administration Manual

The Cisco Linksys PAP2 Administration Manual is a detailed guide that helps you configure and manage your PAP2 device seamlessly. This comprehensive manual is available for free download at manualshive.com, providing users with easy access to relevant information to ensure optimal performance of their PAP2 device.

Share
Download
background image

Configuring SIP, SPCP, and NAT

Configuring SIP

Cisco SPA and Wireless IP Phone Administration Guide

105

5

 

STEP 6

Click Submit All Changes.

Configuring a SIP Proxy Server

To configure SIP proxy and registration parameters:

STEP 1

Log in to the web administration interface. 

STEP 2

Click Admin Login and advanced.

STEP 3

Click the Extension <number> tab. 

STEP 4

Configure the proxy and registration parameters for each extension.

Auth INVITE

When enabled, authorization is required for initial 
incoming INVITE requests from the SIP proxy. 

NOTE:

Not applicable to the WIP310.

Ntfy Refer On 1xx-
To-Inv

If set to yes, as a transferee, the phone will send a NOTIFY with 
Event:Refer to the transferor for any 1xx response returned by 
the transfer target, on the transfer call leg.

If set to no, the phone will only send a NOTIFY for final 
responses (200 and higher).

NOTE:

Not applicable to the WIP310.

Use Anonymous 
with RPID

This parameter applies only if <SIP Remote-Party-ID> is set to 
yes; otherwise, it is ignored.

If the parameter is set to yes, the FROM header's display-name 
and user-id fields are set to anonymous when the caller blocks 
his caller-id. If the parameter is set to no, the FROM header's 
display-name and user-id are not masked. The Remote-Party-
ID header indicates privacy=full when the caller wishes to 
block his caller-id.

Default: yes.

NOTE:

Not applicable to the WIP310.

Set G729 annexb

Configure G.729 Annex B settings.

NOTE

Not applicable to the SPA525G.

Parameter

 Description

Summary of Contents for Linksys PAP2

























































































































































































































































































Reviews:

No comments

Related manuals for Linksys PAP2

D-Link G120 - DNS NAS Server Specification preview
G120 - DNS NAS Server
Brand: D-Link Pages: 2
D-Link Air DWL-120 Features & Benefits preview
Air DWL-120
Brand: D-Link Pages: 2
Weego SAE 12V DC Owner'S Manual & Warranty preview
SAE 12V DC
Brand: Weego Pages: 6
Basalte 0610-20 Installation Manual preview
0610-20
Brand: Basalte Pages: 2
W&T Electronics W&T-AD90W-1N User Manual preview
W&T-AD90W-1N
Brand: W&T Electronics Pages: 4
Parani Parani-SD1100 User Manual preview
Parani-SD1100
Brand: Parani Pages: 48
P+S Technik PS-IMS-F3 User Manual preview
PS-IMS-F3
Brand: P+S Technik Pages: 2
TP-Link TL-WN323G User Manual preview
TL-WN323G
Brand: TP-Link Pages: 33
MiLAN E-FX-HB-1600 Install Manual preview
E-FX-HB-1600
Brand: MiLAN Pages: 1
Goobay 62107 User Manual preview
62107
Brand: Goobay Pages: 5
Digitus DN-70031 Quick Start Manual preview
DN-70031
Brand: Digitus Pages: 6
Jabra LINK 350 Datasheet preview
LINK 350
Brand: Jabra Pages: 2
Cellink BTA-6000R User Manual preview
BTA-6000R
Brand: Cellink Pages: 31
M-system LiBo-8 Instruction Manual preview
LiBo-8
Brand: M-system Pages: 7
GE PACSystems RSTi Manual preview
PACSystems RSTi
Brand: GE Pages: 172
IOGear GUW2015VKIT Installation Manual preview
GUW2015VKIT
Brand: IOGear Pages: 44
Manhattan 150859 Install Manual preview
150859
Brand: Manhattan Pages: 2
Panda Wireless 150Mbps User Manual preview
150Mbps
Brand: Panda Wireless Pages: 10

Brands by name

Popular brands

Load more brands