Chrysler 300 SRT 2010 Owner'S Manual Download Page 46 | Manualshive

Page: 46 / 465

Chrysler 300 SRT 2010 Owner'S Manual Download Page 46

WARNING! (Continued)

•

Wearing your belt in the wrong place could make
your injuries in a collision much worse. You might
suffer internal injuries, or you could even slide out
of part of the belt. Follow these instructions to
wear your seat belt safely and to keep your pas-
sengers safe, too.

•

Two people should never be belted into a single
seat belt. People belted together can crash into one
another in a collision, hurting one another badly.
Never use a lap/shoulder belt or a lap belt for more
than one person, no matter what their size.

Lap/Shoulder Belt Operating Instructions

1. Enter the vehicle and close the door. Sit back and
adjust the front seat.

2. The seat belt latch plate is above the back of your seat.
Grasp the latch plate and pull out the belt. Slide the latch
plate up the webbing as far as necessary to make the belt
go around your lap.

Pulling Out the Lap/Shoulder Belt Latch Plate

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

45

«
...
44
45
46
47
48
...
»

Summary of Contents for 300 SRT 2010


















































































































































































































































































































































































































































































Reviews:

No comments