manualshive.com logo in svg

Chrysler 300 SRT 2010, Owner'S Manual, Page: 343 / 465

Share
Download
Chrysler 300 SRT 2010 Owner'S Manual Download Page 343

NOTE:

•

Refer to the “Vehicle Certification Label” affixed to the
rear of the driver’s door for your vehicle’s GVWR and
GAWRs.

•

Refer to the “Tire Placard” for your vehicle’s proper
tire pressure.

TRAILER TOWING

Trailer towing with this vehicle is not recommended.

RECREATIONAL TOWING (BEHIND
MOTORHOME, ETC.)

Recreational towing is allowed ONLY if the driveshaft
is removed.

Towing with the rear wheels on the ground

while the driveshaft is connected can result in severe
transmission damage.

WARNING!

If the driveshaft is removed, the vehicle can roll even
if the transmission is in PARK, which could cause
serious injury or death.

The parking brake must be firmly engaged and the
wheels chocked during driveshaft removal and installa-
tion. The parking brake must remain engaged unless the
vehicle is securely and properly connected to the tow
vehicle, or the driveshaft is completely reinstalled. See
your authorized dealer for proper driveshaft removal
and

reinstallation

procedures,

including

flange

orientation/alignment, use of thread-locking compound,
proper bolt torque specifications, etc.

342

STARTING AND OPERATING

Summary of Contents for 300 SRT 2010


















































































































































































































































































































































































































































































Reviews:

No comments