manualshive.com logo in svg

Chrysler 300 SRT 2010, Owner'S Manual, Page: 361 / 465

Share
Download
Chrysler 300 SRT 2010 Owner'S Manual Download Page 361

CAUTION!

•

When “rocking” a stuck vehicle by moving be-
tween 1st and REVERSE, do not spin the wheels
faster than 15 mph (24 km/h), or drivetrain damage
may result.

•

Revving the engine or spinning the wheels too fast
may lead to transmission overheating and failure.
It can also damage the tires. Do not spin the
wheels above 30 mph (48 km/h) while in gear (no
transmission shifting occurring).

WARNING!

Fast spinning tires can be dangerous. Forces gener-
ated by excessive wheel speeds may cause damage, or
even failure, of the axle and tires. A tire could
explode and injure someone. Do not spin your vehi-
cle’s wheels faster than 30 mph (48 km/h) or for
longer than 30 seconds continuously without stop-
ping when you are stuck and do not let anyone near
a spinning wheel, no matter what the speed.

TOWING A DISABLED VEHICLE

Without The Ignition Key Fob

Special care must be taken when the vehicle is towed
with the ignition in the OFF position. The only approved
method of towing without the ignition key is with a
flatbed truck. Proper towing equipment is necessary to
prevent damage to the vehicle.

360

WHAT TO DO IN EMERGENCIES

Summary of Contents for 300 SRT 2010


















































































































































































































































































































































































































































































Reviews:

No comments