manualshive.com logo in svg

Chrysler 300 SRT 2010, Owner'S Manual, Page: 375 / 465

Share
Download
Chrysler 300 SRT 2010 Owner'S Manual Download Page 375

WARNING!

•

Battery fluid is a corrosive acid solution and can
burn or even blind you. Do not allow battery fluid
to contact your eyes, skin, or clothing. Do not lean
over a battery when attaching clamps. If acid
splashes in eyes or on skin, flush the area imme-
diately with large amounts of water.

•

Battery gas is flammable and explosive. Keep
flame or sparks away from the battery. Do not use
a booster battery or any other booster source with
an output greater than 12 Volts. Do not allow cable
clamps to touch each other.

•

Battery posts, terminals, and related accessories
contain lead and lead compounds. Wash hands
after handling.

(Continued)

WARNING! (Continued)

•

The battery in this vehicle has a vent hose that
should not be disconnected and should only be
replaced with a battery of the same type (vented).

CAUTION!

•

It is essential when replacing the cables on the
battery that the positive cable is attached to the
positive post and the negative cable is attached to
the negative post. Battery posts are marked posi-
tive (+) and negative (-) and are identified on the
battery case. Cable clamps should be tight on the
terminal posts and free of corrosion.

•

If a “fast charger” is used while the battery is in
the vehicle, disconnect both vehicle battery cables
before connecting the charger to the battery. Do
not use a “fast charger” to provide starting voltage.

374

MAINTAINING YOUR VEHICLE

Summary of Contents for 300 SRT 2010


















































































































































































































































































































































































































































































Reviews:

No comments