Home
/
Chrysler
/
300 SRT 2010
/
Owner'S Manual

Chrysler 300 SRT 2010, Owner'S Manual, Page: 172 / 465

Share

Page: 172 / 465

Chrysler 300 SRT 2010 Owner'S Manual Download Page 172

POWER SUNROOF — IF EQUIPPED

The power sunroof switch is located between the sun
visors on the overhead console.

WARNING!

•

Never leave children in a vehicle with the key in
the ignition switch (or the ignition in the ACC or
RUN position, when using Keyless Go™). Occu-
pants, particularly unattended children, can be-
come entrapped by the power sunroof while oper-
ating the power sunroof switch. Such entrapment
may result in serious injury or death.

•

In an accident, there is a greater risk of being
thrown from a vehicle with an open sunroof. You
could also be seriously injured or killed. Always
fasten your seat belt properly and make sure all
passengers are also properly secured.

•

Do not allow small children to operate the sun-
roof. Never allow your fingers, other body parts, or
any object, to project through the sunroof opening.
Injury may result.

Power Sunroof Controls

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

171

«
...
170
171
172
173
174
...
»

Summary of Contents for 300 SRT 2010


















































































































































































































































































































































































































































































Reviews:

No comments